新闻动态 |
中走丝线切割工件装夹的注意事项 1、 工件装夹前必须先清理干净锈渣、杂质。 2、 模板、型板等切割工件的安装表面在装夹前要用油石打磨修整,防止表面凹凸不平,影响装夹精度或与下喷嘴干涉。 3、 工件的装夹方法必须正确,确保工件平直紧固。 4、 严禁使用滑牙螺钉。螺丝钉锁入深度要在8mm以上,锁紧力要适中,不能过紧或过松。 5、 压块要持平装夹,保证装夹件受力均匀平衡。 6、 装夹过程要小心谨慎,防止工件(板材)失稳掉落。 7、 工件装夹的位置应有利于工件找正,并与机床行程相适应,利于编程切割。 8、 工件(板材)装夹好后,必须再次检查确认与机头,极间线等是否干涉现象。 The matters needing attention in WEDM workpiece clamping. 1, workpiece must first clean the rust slag, impurity clip before. The mounting surface cutting the workpiece 2, template, template to use oilstonegrinding the dressing in clamping the front, to prevent uneven surface and theinfluence of clamping precision or interfere with the nozzle. 3, workpiece clamping method must be correct, ensure the workpiece straightnessfastening. 4, prohibited the use of sliding screw. Screw locking depth in 8mm above, clamping force should be moderate, not too tight or too loose. 5, a pressing block to ensure the paperback clamp, clamping pieces of uniform stressbalance. 6, the clamping process should be careful to prevent the workpiece (sheet) instabilityfall. 7, a workpiece clamping position should be conducive to the workpiece is looking to adapt and stroke of machine tool, cutting to programming. 8, the workpiece clamping (plate) good, should be examined and the head again, pole to pole line and whether the interference phenomenon. |
目前公司已在全国多地建立较为完善的销售网络,同时产品行销东南亚、日本等国家。
产品广泛应用于模具、电子仪器、精密机械、汽车零部件、军工、高校等企业及相关领域;产品严格遵守数控机床要求生产,凭着雄厚的研发能力,精湛的生产工艺,完善的售后服务,多年积累的经验,在业界赢得良好口碑。
线切割,电火花机母板LED1(母板24V電源指示燈): 24V電源接通,指示燈亮。LED2(深孔指示燈):深孔開,指示燈亮。LED3(大面積指示燈):大面積開,指示燈亮。LED4(開機初始化指示燈):開機延時一段時間後該指示燈亮,機床結束待制作:木木 苏州阿尼拉数控科技有限公司
线切割机,火花机033(邏輯板)指示灯说明LED4(033板24V電源指示燈):24V電源接通,指示燈亮。LED5(Z軸向下運動指示燈):Z軸向下運動,指示燈亮。LED6(Z軸向上運動指示燈):Z軸向上運動,指示燈亮。LED7(Z軸鎖定指示燈):Z軸運動,指示燈亮。LED(033板5V電源指示燈):5V電源接通,指示燈亮。制作:木木 苏州阿尼拉数控科技有限公司
电火花线切割,火花机043(解碼板)指示灯说明 燈號伺服速度LED1LED2LED3LED41亮2亮3亮亮4亮5亮亮6亮亮7亮亮亮8亮9亮亮LED5(上定位指示燈):到達上定位,指示燈亮。LED6(極性指示燈):極性開,指示燈亮。LED7(下定位指示燈):到達下定位,指示燈亮。LED8(LED5V):5V電源接通,指示燈亮。LED9(LED24V):24V電源接通,指示燈亮。制作:木木 苏州阿尼拉数控科技有限公司